Merge from bittboy/buildroot@db180c0

board/sifive/hifive-unleashed/genimage.cfg

@@ -0,0 +1,17 @@
+image sdcard.img {
+	hdimage {
+		gpt = true
+	}
+
+	partition bootloader {
+		image = "fw_payload.bin"
+		offset = 1M
+		size = 32M
+		partition-type-uuid = 2E54B353-1271-4842-806F-E436D6AF6985
+	}
+
+	partition rootfs {
+		image = "rootfs.ext4"
+		partition-type-uuid = 0FC63DAF-8483-4772-8E79-3D69D8477DE4
+	}
+}

board/sifive/hifive-unleashed/linux.config.fragment

@@ -0,0 +1,16 @@
+CONFIG_HZ_100=y
+CONFIG_CMDLINE="earlycon=sbi root=/dev/mmcblk0p2 rootwait"
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_SERIAL_SIFIVE=y
+CONFIG_SERIAL_SIFIVE_CONSOLE=y
+CONFIG_SPI=y
+CONFIG_SPI_SIFIVE=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_SIFIVE=y
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+CONFIG_CLK_U54_PRCI=y
+CONFIG_CLK_GEMGXL_MGMT=y
+CONFIG_PWM=y
+CONFIG_PWM_SIFIVE=y

board/sifive/hifive-unleashed/readme.txt

@@ -0,0 +1,75 @@
+SiFive HiFive Unleashed
+=======================
+
+This file describes how to use the pre-defined Buildroot
+configuration for the SiFive HiFive Unleashed board.
+
+Further information about the HiFive Unleashed board can be found
+at https://www.sifive.com/boards/hifive-unleashed
+
+Building
+========
+
+Configure Buildroot using the default board configuration:
+
+  $ make hifive_unleashed_defconfig
+
+Customise the build as necessary:
+
+  $ make menuconfig
+
+Start the build:
+
+  $ make
+
+Result of the build
+===================
+
+Once the build has finished you will have the following files:
+
+    output/images/
+    +-- fw_jump.bin
+    +-- fw_jump.elf
+    +-- fw_payload.bin
+    +-- fw_payload.elf
+    +-- Image
+    +-- rootfs.ext2
+    +-- rootfs.ext4
+    +-- rootfs.tar
+    +-- sdcard.img
+
+
+Creating a bootable SD card with genimage
+=========================================
+
+Buildroot builds a SD card image for you. All you need to do is dd the
+image to your SD card, which can be done with the following command:
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/mmcblk0 bs=4096
+
+Booting the SD card on the board
+================================
+
+Make sure that the all DIP switches are set to the off position for
+default boot mode (MSEL mode = 1111), insert the SD card and power
+up the board.
+
+Connect the USB cable and open minicom (/dev/ttyUSB1, 115200, 8N1).
+
+See the 'SiFive HiFive Unleashed Getting Started Guide' for
+more details (https://www.sifive.com/documentation).
+
+You will get a warning reported by fdisk when you examine the SD card.
+This is because the genimage.cfg file doesn't specify the SD card size
+(as people will naturally have different sized cards), so the
+secondary GPT header is placed after the rootfs rather than at the end
+of the disk where it is expected to be.
+
+You will see something like this at boot time:
+
+[    2.318722] GPT:Primary header thinks Alt. header is not at the end of the disk.
+[    2.325390] GPT:190496 != 122142719
+[    2.328843] GPT:Alternate GPT header not at the end of the disk.
+[    2.334824] GPT:190496 != 122142719
+[    2.338302] GPT: Use GNU Parted to correct GPT errors.
+[    2.343456]  mmcblk0: p1 p2